Instruction manual • Read online or download PDF • Futaba 12Z User Manual. Futaba 12Z User Manual • Motor • Futaba Accessories communication. Read online or download PDF • Page / • Futaba 12Z User Manual • Futaba Accessories communication.

Author: Tygokazahn Yom
Country: Solomon Islands
Language: English (Spanish)
Genre: Politics
Published (Last): 14 December 2010
Pages: 365
PDF File Size: 2.41 Mb
ePub File Size: 18.71 Mb
ISBN: 788-7-59381-849-5
Downloads: 5161
Price: Free* [*Free Regsitration Required]
Uploader: Daikinos

Got it, continue to print. Terms of Use Privacy Policy. Updating following procedure to update the program. It is used Fine tuning to correct undesirable tendencies when rudder is applied in roll maneuvers, knife edge, etc. Thank you, Horizon Hobby.

Display adjustment and auto power off setting. For PCM mode, you can set eight linear fufaba and one digital channel. Page Operation modes Symmetrical box mode The operation modes when stick, trim lever, or but left and right up and down operation is knob was selected are described below.

Futaba® – Contact Us

Curve setting operation This section describes the setting procedure of curves which are used with the AFR function and each Curve type selection Curve type selection 1.

If the battery fully discharges during During writing, the bar graph moves to the right. The setting screen appears. The screen depends on the model type. Equipment for reading and writing CF cards are available at most electronics stores.

Mixing applied in other swash modes is different, but the setting procedure is the same. Before Use T12Z is operated by 7. Connect the receiver and servos to match the type used. The preset elevators and flaps camber flap, brake flap offset amount can be activated by a switch. Enter text from picture: For retail sales of Futaba, please visit your local dealer or Tower Hobbies.


PIT to RUD mixing Revolution mixing Use this mix when you want to suppress the However, when a GY Series or other heading reaction torque generated by main rotor pitch and hold gyro is used, since correction is performed speed changes at pitch operation.

FUTABA 12Z Series Manuals

Remember, if the predefined control suddenly This function only works with G3 or PCM receivers moves to a position you did not command, land at If you later change model commands that apply to helicopters only. Comments to this Manuals Your 12s. Two independent timers are provided for your use. To add new models or to call a model already set, use the Model Select function of the Linkage Menu.

Prior approval of the appropriate government authorities may be required. Use only the Futaba lithium ion transmitter charger included with this set for, or other chargers approved by Futaba to charge the Uftaba batteries in the 1 Z transmitter.

Never hold the antenna alone. SWASH MIX Example of use The swash mix function is used to correct the swash plate in the aileron roll direction and elevator cyclic pitch corresponding to each undesirable tendencies in the roll direction operation of each condition.

Setting method enter a point and push the enter button. Updating procedure seconds, updating starts. By pressing ‘print’ button you will print only current page. The action is not functional at high throttle to avoid accidental dead sticks. Page 74 be used for each condition. It will prevent the engine from racing dangerously when adjusting the Idle-Up settings.

Function, Functions of linkage menu, Function change | Futaba 12Z User Manual | Page 55 /

Switch selection method lever, or VR are used as a switch setting method is common to all functions. Flight condition’s addition, deletion, copy, condition renaming, and condition delay can be set.


A needle curve can be set. Do not use the transmitter as it is, send it to the Futaba Service Center.

manjal Page 86 Setting method [Fine tuning VR operation mode] turn the data input dial to the left and push the enter and counterclockwise, the mixing r a t e i n c r e a s e s a n d d e c r e a s e srespectively.

Although your 12Z protects the model memories with non-volatile EEPROM memory which does not require periodic replacement and not a battery, it still should have regular checkups. For PPM mode, you can set only eight linear channels. The differential rate can also be adjusted according to the flying state by Note: We recommend sending your system to the Futaba Service 21z annually during your non-flying season for a complete checkup cutaba service.

Functions and mixing functions necessary for each model type are set in advance at the factory. Use the Normal mode as long as there is no special reason to use the Reverse fytaba. Page 34 digit, use the cursor lever to select the arrow symbol and move the arrow symbol by pushing the enter button.

When using this function, always check initial operation with the propeller removed. Page 41 Use this function when you want to suppress the torque generated by the changes in the pitch and speed of the main rotor during pitch operation.