American DJ ®. User Instructions. 1. 2. 3. 4. 9. 5. 6. 7. 8. DMX MIDI. SCENE SETTER™. C A P A B L E. 16 5m. MINS. SHOW. MODE.1Sec. SCENE SETTER Elation Professional R Read the instruction in this manual carefully and thoroughly, as they give important. ELATION. PROFESSIONAL. SCENE SETTER. TI. 24 CH Dimmer Console . Read the instruction in this manual carefully and thoroughly, asthey give important.
|Published (Last):||11 October 2016|
|PDF File Size:||4.81 Mb|
|ePub File Size:||17.42 Mb|
|Price:||Free* [*Free Regsitration Required]|
This button is used to activate the unit s program mode. HI I have read the manual a zillion times, can you tell me where the assign to channel is described?
The Take-2 is a state-of-the-art message-on-hold More information. The chase rate will be synchronized to the time interval of the last two taps. You may press and hold down the relevant Flash button to trigger the program. If any accessories are shipped with the product, Elation shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.
Be sure main power is off.
ADJ Scene Setter 24 Channel Dimming Console – MIDI Functions & DMX Dimming Control
Does not include any cables or power supply, only the test. I spend over an hour on the phone with ADJ support, they could not figure it out, then promised to call back that day, days ago, not holding my breath. Every has been thoroughly.
Please feel free to send us your questions by clicking here. Be sure this unit has been in Record mode. In the unlikely event your unit may require service please contact your nearest Elation dealer. Every has been thoroughly More information.
Page of 12 Go. To optimize the performance of this product, please. Take-2 by Nel-Tech Labs, Inc. Information, specifications, diagrams, images, and instructions herein are subject to change without notice.
I am new to using a Scene Setter 24 and it seems like there are stored test. Just manually program the DMX channels on the strobe and match them with the. The LED indicators will directly reflect the changes in slider level. Toll-free telephone support If you More information.
Elation STAGE SETTER-8 User Instructions
Every has been thoroughly tested and. Videos There are currently no videos available for this product. Digital Photo Picture Scenr. Table of Contents Add to my manuals Add. Press and hold the Record button. Flash button 1 Tap this button three times 2. Every has been thoroughly tested and has More information. Before your initial start-up, please make sure.
STAGE SETTER-8. User Instructions. Elation Professional
Playback options include automated, sound-activated or manual RGB color mixing. Please read before use. General Elatino General Instructions Read the instruction in this manual carefully and thoroughly, as they give important information regarding safety during use and maintenance. Once Program mode has been activated, tap the Bump Button that corresponds to a Scene Y slider that will be used to store the scene.
Once Program Mode is activated stter may begin to program chase patterns or static scenes into the eight eelation Pattern Buttons Elation Professional – www.
The consumer s and or Dealer s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall Elation be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.
Nsi if I recall used this type of setup in their 72xx series inorder to be able to link two controllers, universes were still independant but there was some linking Second question, is there any patching available to assign a fader in the manual mode to a different dmx address? The has three different operating modes: Every has been thoroughly tested and has. Disconnect from main power before making any settter of connection.
Coemar Manual System 12 Plus. Elation Profesional – www. All products covered by this warranty were manufactured after January 1,and bear identifying marks to that effect. In 1×16 mode, the Y Crossfader controls the scene Fade Time.
This button is used to disable all channel output To order call To initiate programming, first tap the Program Button 14 so that the Program to activate program mode, the program LED will glow when program mode is activated. General Introduction Sceme Instructions Unpacking: This console receives MIDI program changes according the following table: Do not attempt to operate this unit if the power cord has been frayed or broken.
My next problem is on ths scene setter, I simply cannot get it to go into record mode to even try the solution. Your cables should be made with a male and female XLR connector on either end of the cable.
The 8 momentary Bump Buttons are used to bring each individual channel to full intensity regardless of the Blackout 15 function or the Master Level 8 setting.