DATASHEET 2N2219 PDF

The 2N, 2N, 2N and 2N are sili- con planar TO (for 2N and 2N) and in Jedec . This datasheet has been download from. Semelab encourages customers to verify that datasheets are current before Test Conditions. Min. Typ. Max. Unit. LAB. SEME. 2N IC = 10mA. IB = 0. Sep 2. Philips Semiconductors. Product specification. NPN switching transistors. 2N; 2NA. FEATURES. • High current (max.

Author: Yozshudal Akinomi
Country: Bhutan
Language: English (Spanish)
Genre: Medical
Published (Last): 16 July 2013
Pages: 190
PDF File Size: 17.47 Mb
ePub File Size: 17.63 Mb
ISBN: 420-8-35431-817-6
Downloads: 51513
Price: Free* [*Free Regsitration Required]
Uploader: Nacage

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project. Submitted by admin on 21 June Another important thing to keep in mind, while using a transistor as switch is the base resistor.

Since transistor is of NPN the load to be switched should be connected n22219 the collector and the emitter should be connected to the ground as show in the figure below. In our case for a collector current of mA we have to pass a base current of 16mA.

2N Datasheet(PDF) – NXP Semiconductors

So to calculate the resistor value of the base we can use the formulae. Current flows in through collector, normally connected to load. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Here lets us assume the load here consumes around mA maximum so our collector current I C mA. Where h FE, is the current gain of the transistor which in our case is To make this current flow through the transistor the value of base current I B can be calculated using the below formula:.

  EUBACTERIA DAN ARCHAEBACTERIA PDF

The value of this current can be calculated by the required amount of current that will be consumed by the load. Complete Technical Details can be found at the datasheet given at the end of this page.

But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. This stage is called Saturation Region. TL — Programmable Reference Voltage.

To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the maximum current from the transistor. Amplifier modules like Audio amplifiers, signal Amplifier etc. When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter.

But this calculation will lead to the closest value to start with. So the value if R B will be.

  BJORK BIOPHILIA BOOKLET PDF

Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. The 2N is a NPN transistor and is normally used as a switch in many circuits. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

2N2219 Datasheet, Equivalent, Cross Reference Search

Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1. As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. This resistor is connected to the base pin of the transistor to limit the current flowing through the base. Current Drains out through emitter, normally connected to ground.