ASTM B153 PDF

B – 11 Standard Test Method for Expansion (Pin Test) of Copper and Copper- Alloy Pipe and Tubing, copper, copper alloy, expansion, expansion test, pin. This standard is issued under the fixed designation B ; the 1 This test method is under the jurisdiction of ASTM Committee B05 on Copper. Find the most up-to-date version of ASTM B at Engineering

Author: Shakagrel Kazigrel
Country: Guinea
Language: English (Spanish)
Genre: Spiritual
Published (Last): 16 September 2005
Pages: 56
PDF File Size: 13.10 Mb
ePub File Size: 10.18 Mb
ISBN: 387-9-91278-138-5
Downloads: 94707
Price: Free* [*Free Regsitration Required]
Uploader: Brashura

Except as otherwise speci? This list is incomplete ; you can help by expanding it. When suitable equipment is not available for determining the speci? A standard may be withdrawn with or without replacement.

ASTM B153 – 11(2017)

This list may include either current or withdrawn standards. Limits for unnamed elements are to be established by agreement between manufacturer or supplier and purchaser. Your comments are invited either for revision of this standard or for additional standards asmt should be addressed to ASTM International Headquarters. Prefix letters correspond to the following subjects:.

From Wikipedia, the free encyclopedia. Rectangular including square tubes shall normally be supplied only in drawn general-purpose temper.

A withdrawn standard has been discontinued by its sponsoring committee. Grossman the Grossman method.

Alternatively, if the manufacturer uses speed-insensitive eddy-current units that are equipped so that a fraction of the maximum unbalance signal is able to be selected, the following percent maximum unbalance signals shall be used. Drawn temper is for general purposes and is most commonly used where there is no speci? A number in parentheses indicates the g153 of last reapproval.

Any evidence of leakage shall be cause for rejection. The notchdepth tolerance shall be Workmanship, Finish, astk Appearance Standard Specification for Ferrotitanium. Supplementary requirement S5 shall apply only when speci? Standard Specification for Ferrocolumbium Ferroniobium.

  CITANKA ZA 4 RAZRED GIMNAZIJE PDF

Hard-drawn temper is used only where there is need for a tube as strong as awtm commercially feasible for the sizes indicated. Last previous edition B — Screening and resubmittal of samples from rejected lots for visual and dimensional examination is acceptable. C Although no minimum grain size is speci? C on tube sizes greater than 5 in. Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor aztm astm.

Former soft anneal soft anneal light anneal light anneal soft anneal soft anneal light anneal light anneal soft anneal soft anneal up to 0. Copper plus sum of all named b53 shall be Grade B7 Studs bolts and Grade B16 Studs bolts fall in this category and are used for high temperature, high-pressure environments like petroleum industry.

List of ASTM International standards

Tubes for Voice and Pneumatic Service S5. Ten alloys are speci? D Light-drawn and hard-drawn tempers are available in round-tube only.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned in this standard.

ASTM B无缝黄铜管_百度文库

Incomplete lists from February This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Standard designations usually consist of a letter prefix and a sequentially assigned number.

All defective items shall be replaced with acceptable items before lot acceptance. Light-drawn bending temper is used only when a tube of some stiffness but yet capable of being bent is needed. C Rockwell hardness values shall apply only to 1b53 having a wall thickness of 0. The tension test for other sizes of tubes need not be made except when indicated by the purchaser at the time of placing the order.

  ALEXIS DE TOCQUEVILLE DESPRE DEMOCRATIE IN AMERICA PDF

The manufacturer shall select the nondestructive test that is most suitable for the tube size and the application. Use equipment for the detection n153 removal of mercury vapor.

When, in the case where subsequent testing by the purchaser establishes that the material does not meet these requirements, then the tubes shall be subject to rejection. Rockwell hardness values shall apply only to tubes having a wall thickness of 0.

Standard Specification for Ferromanganese. Tube ordered in the drawn H condition is not subject to this test. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend. Rockwell hardness tests shall be made on the inside surface of the tube.

Norma ASTM B()

The test method used shall provide for easy visual detection of any leakage, such as by immersion of the tube under water or by the pressure differential method. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility.

For any combination of diameter and wall thickness not covered under hard-drawn temper, the values given for drawn temper shall be used.

When there is a need for light-drawn or hard-drawn tempers these are to be supplied as agreed upon between the manufacturer and the purchaser. Standard Specification for Steel Track Spikes.

When agreement on the Rockwell hardness tests cannot be reached, the tensile strength requirements of Table 2 shall be the basis for acceptance or rejection. Dimensions and Permissible Variations Wear rubber gloves when conducting the test.