AMS C 26074 PDF

Find the most up-to-date version of SAE AMS-C at Engineering MIL-CC. 3 MY les5. MILITARY SPECIFICATION. This specification ie approved for we by all. Departfmnta and Agencie8 of the Oapartmmt of. Defense. 1. SAE AMS-C Electroless Nickel Coatings. SAE AMS-C Revision D, June Complete Document. Electroless Nickel Coatings. Includes all.

Author: Shagal Grozuru
Country: Belarus
Language: English (Spanish)
Genre: Politics
Published (Last): 21 February 2010
Pages: 364
PDF File Size: 18.49 Mb
ePub File Size: 1.89 Mb
ISBN: 781-8-50427-806-2
Downloads: 5363
Price: Free* [*Free Regsitration Required]
Uploader: Samujin

Composites can be plated directly by using special pretreatments to prevent the basis material from contaminating the bath or to obtain adequate coating adhesion.

The nickel coatings shall be classified in accordance with the thermal treatment applied subsequent to plating.

With aluminum electronic devices, not only is product contamination prevented, but the coated parts facilitate soldering when used in conjunction with a mildly activated RMA or activated RA rosin flux. The selected samples shall be subjected to a sustained tensile load equal to percent of the maximum design yield load for which the part was designed.

AMS-C-26074 and MIL-C-26074 – An explanation of the revision path

AMS-CB is therefore reinstated 20674 is designated as a noncurrent document. As you can see by my posting, the MIL-C has had a long strange history! Our drawing states to process parts to MIL-C The separate test specimens used for salt-spray testing shall be 4 inches by 6 inches. Military Specification MIL-CE, and contains only minor editorial and format changes required to bring it into conformance with the publishing requirements of SAE technical standards.

The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole responsibility of the user. However, it is not advised for new design.


SAE AMS-CB 化学镀镍(英文)_百度文库

Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements ame herein, unless disapproved by the Government.

Thanks so much for asking, Ed: Unfortunately, the MIL-C was not cancelled at that point in time. You can order through our website at www. Each of the sample parts selected in accordance with 4. In order to post comments, please make sure JavaScript and Cookies are enabled, and reload the page. Equivalent basis material includes chemical composition and surface finish prior to coating application.

Your email address will not be published. asm


For example, a cold-rolled steel surface shall not be used to represent a hot-rolled steel surface; owing to the impracticability of forging or casting separate test specimens, hot-rolled steel specimens may be used to represent forged and cast steel parts. Required 260774 can be achieved by heating using the 2674 schedule: Excellent uniform deposits are produced on irregular parts.

The coating adhesion after completion of all processing and thermal treatments shall be such that when examined at a magnification of 4X, the coating shall not show separation from the basis metal when tested in accordance with ASTM B as specified in 4.

Click here for instructions on how to enable JavaScript in your browser. TSB rules provide for a the publication of portions of unrevised government specifications and standards without consensus v at the SAE Committee level, and b the use of the existing government specification or standard format. Aluminum alloys, heat-treatable, processed to improve adhesion of the nickel deposit. The Aerospace Materials Division, however, does not recommend these specifications for future use in new designs.


The articles, parts or test specimens shall be held under load for at least hours and then examined for fracture.

Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the government to accept defective material.

The lot shall be rejected if any coated article, part, or test specimen shows cracking or fracture of the basis metal.

A hardness test shall be run once a month, on four randomly selected parts representing the months production, or on four separately coated specimens as specified in 4. Class and amz, and heat treatment or condition see 1. Heat treatment increases coating magnetism.

Class 2 hardness coatings: This is a stabilized document.

Unless otherwise specified, the a,s peening shall be accomplished on all surfaces for which the coating is required and all immediately adjacent surfaces when they contain notches, fillets or other abrupt changes of section size where stresses will be concentrated. Formation of cracks that do not result in loss of plating adhesion is acceptable.

A hydrogen embrittlement relief test shall be run once per month on a random sample of 4 parts as specified in 4.