Again, we appreciate your selection of an Airtronics Radio Control System and wish you many hours of flying enjoyment. RD Transmitter Specifications. AIRTRONICS. RD Radio System. Operating Manual. INTIMES no! Airplane Thank you for selecting the Airtronic RD Radio System. In deigning the. download airtronics rd manual. I need a owners manual for an Airtronics RD radio (not the super).. I found one here, but it’s $

Author: Samujar Aragul
Country: Myanmar
Language: English (Spanish)
Genre: Automotive
Published (Last): 4 June 2011
Pages: 316
PDF File Size: 5.51 Mb
ePub File Size: 11.69 Mb
ISBN: 615-6-28131-290-9
Downloads: 48455
Price: Free* [*Free Regsitration Required]
Uploader: Dim

Reinstall the transmitter rear case and be careful when placing over ther NiCd battery connector pins.


This is a good starting point for determining the suitability of Exponential throw for you aircraft and flying style. Note that the rudder servo will still respond to rudder stick movement as well airttronics with aileron stick movement.

Normally during training, the instructor takes the model off and flies it to a reasonable altitude. We further certify that the necessary measurments were.

It is not necessary for the student to hold the trainer switch on the Trainer transmitter.

Now you can add rudder to aileron mix. In the following example, we will assume you want to have separate servos for aileron control. Adding some down elevator will help reduce it.

Above items will also work with Airtronics Quasar, Radiant, and Vanguard transmitter batteries.

Airtronics RD – RC Groups

The four flight modes are: The RD Manua can control the following types: To print the manual completely, please, download it. Turn on the Master transmitter and the Model. The Actual speed of signal processing and servo movement are not affected by the Dual Rate settings, only the amount of total throw available. For additional information, see the Global Shipping Program terms and conditions – opens in a new window or tab.


The cable will energize the encoder section airfronics the Trainer transmitter. This manuall has ended. The Elevator channel will appear on the upper part of the screen. Again, we appreciate your selection of an Airtronics Radio Control System and wish you many hours of flying enjoyment. I will have completed a successful radio equipment ground range check before the first flight of a new or repaired model.


An extremely versatile feature of the RD Super transmitter is the capability to select 4 different types of modulation. A new, unread, unused book in perfect condition with no missing or damaged pages.

The screen will look like the following illustration. Seller assumes all responsibility for this listing.

See all condition definitions – opens in a new window or tab The purpose of a Compensation Mixer is to allow one transmitter control input to affect two flight functions.

Both transmitters must be programmed identically for the trainer system to function properly. Normally you set your throttle stick in the extreme low position and use EPA and the digital trim to obtain a steady low engine idle speed.

Now screw Part A in or out to the desired airtgonics and lock it in place by screwing Part B against it. When the Bar Graph reads less than half you should not fly until you recharge the transmitter. The default positions are as indicted. The range of values and default settings for each is shown below. For instance, if you have your aircraft program aiirtronics Model 1 and nothing in Model 3, you can copy the Model 1 program into Model 3 with the copy function.


Changes the linear movement of the servo to the relation of the stick mabual. This allows you to experiment with different control options without changing your original parameters in this example Model 1. Once the screws are removed swing the back of the case away from mnual transmitter being careful of the trainer plug wiring. In general, large amounts of Exponential are useful only in instances where very large control surface deflection is required at extreme throw, while very small amounts of control response are necessary for smaller control stick inputs.

If you desire, you can display the Integral Timer function instead of the STW stop watch function on all of the Channel screens. To use or modify one of the model setups you first must select M-SL in rx etc menu.